Maintenance

Quick Answer Replace sediment pre-filters every 3-6 months, carbon filters every 6-12 months, RO membranes every 2-5 years, and UV lamps annually. Signs your filter needs changing include reduced water flow, changed taste or odor, discolored water, and exceeding the manufacturer’s rated gallon capacity. Using a filter past its lifespan reduces its effectiveness and can allow contaminants to pass through or even release previously captured contaminants back into your water. Why Timely Filter Replacement Matters Water filters have a finite capacity to capture contaminants. As filter media becomes saturated, its ability to remove contaminants decreases progressively. An overused carbon filter may actually release absorbed chemicals back into filtered water through a process called desorption. An overused sediment filter restricts flow, increases system pressure, and can allow particles through as the media breaks down. Regular filter replacement is not just a maintenance task — it is essential for your water treatment system to actually deliver the clean water you expect. Filter Replacement Schedule by Type Filter Type Typical Lifespan Rated Capacity Key Signs of Exhaustion Sediment pre-filter (5 micron) 3-6 months 5,000-20,000 gallons Reduced flow rate; visible discoloration of filter Carbon block / GAC 6-12 months 5,000-20,000 gallons Chlorine taste returns; odor changes RO membrane 2-5 years N/A (rated by rejection %) TDS creep (rising TDS in permeate); reduced output Inline post-carbon (polishing) 12 months 2,500-5,000 gallons Taste changes in RO water UV lamp 12 months (9,000 hours) N/A (output degrades) UV intensity alarm; annual schedule UV quartz sleeve 2-3 years N/A Visible mineral deposits; scratches; etching Water softener resin 10-15 years N/A Hardness breakthrough despite salt; resin fragments in water Whole-house carbon tank 3-5 years (media) 500,000-1,000,000 gallons Chlorine breakthrough; taste/odor changes Sediment Pre-Filters: Your First Line of Defense Sediment pre-filters capture sand, silt, rust, and other particles before they reach finer filtration stages. Available in 1, 5, 10, and 20-micron ratings, they protect downstream filters and RO membranes from premature clogging. On well water with high sediment, you may need to replace these every 1-3 months. On clean municipal water, 6-month intervals are common. Spun polypropylene and pleated polyester are the two main types. Pleated filters have more surface area and can be rinsed and reused a few times before replacement, making them more economical for high-sediment applications. Carbon Filters: Chlorine, Taste, and Chemical Removal Carbon filters use adsorption to capture chlorine, VOCs, pesticides, and organic chemicals. The two main types are granular activated carbon (GAC) and carbon block. Carbon block filters provide finer filtration and more consistent performance but have higher pressure drop. GAC filters allow higher flow rates but may channel (water finds the path of least resistance through the carbon bed). The simplest way to tell if your carbon filter is exhausted is the return of chlorine taste or smell. If your municipal water normally has a noticeable chlorine taste and that taste returns, your carbon filter needs replacement. A chlorine test strip ($5-$10 for a pack) provides a more precise measurement. RO Membranes: The Heart of Your RO System RO membranes are the most expensive filter component to replace but last the longest. A quality membrane lasts 2-5 years depending on feed water quality, pre-filtration effectiveness, and usage volume. Monitor membrane performance by measuring the TDS of your permeate (filtered) water with a digital TDS meter ($10-$15). When permeate TDS exceeds 10-15% of feed water TDS, the membrane is losing rejection capability and should be replaced. Pre-filtration is critical for membrane longevity. Chlorine destroys RO membranes rapidly, and hard water causes scaling. Ensure your carbon pre-filter and water softener (if applicable) are maintained properly to protect your membrane investment. How to Replace Common Water Filters Under-Sink RO System Filters Turn off the feed water supply valve to the RO system Open the RO faucet to depressurize the system Place a towel under the filter housings to catch drips Unscrew the filter housing using the included wrench (turn counterclockwise) Remove the old filter and discard Clean the housing interior with warm water (no soap) Insert the new filter, ensuring proper orientation Hand-tighten the housing, then snug with the wrench (do not overtighten) Turn on the feed water and check for leaks Flush the first 2-3 tanks of water to remove carbon fines and manufacturing residues Whole-House Filter Cartridges Turn off the main water supply upstream of the filter housing Open a downstream faucet to release pressure Place a bucket under the housing to catch water Unscrew the housing sump using the included wrench Remove the old cartridge and inspect the O-ring for damage Lubricate the O-ring with food-grade silicone grease Insert the new cartridge Reinstall the housing and hand-tighten, then snug with wrench Slowly turn on the water supply and check for leaks Run water through the system for 5 minutes before using Where to Buy Replacement Filters Always use filters that match your system’s specifications. Using incorrect filter sizes or off-brand cartridges that do not meet the original specifications can compromise filtration performance and void your warranty. AMPAC Water Systems provides replacement filters and membranes for all AMPAC systems, with guaranteed compatibility and certified performance. When purchasing replacement filters, verify the exact model number, dimensions, and connection type. For RO membranes, match the GPD (gallons per day) rating. For carbon filters, check the micron rating and NSF certifications. Key Takeaway: Your water treatment system is only as effective as its newest filter. Set calendar reminders for replacement schedules, monitor water taste and flow rate as early warning signs, and always use manufacturer-specified replacement filters. Proper maintenance turns a one-time purchase into years of reliable, clean water for your household. Contact AMPAC Water Systems for replacement filter recommendations and technical support. Frequently Asked Questions How do I know when to change my water filter? Watch for these signs: reduced water flow or pressure, return of chlorine taste or odor, rising TDS readings (for RO systems), visible discoloration of the filter cartridge, and reaching the manufacturer’s recommended replacement date or gallon capacity. A combination of scheduled